Template:TemplateUbootCommands: Difference between revisions

From Wiki-DB
Jump to navigationJump to search
← Older edit
Lzenz (talk | contribs)
635 edits
Lzenz (talk | contribs)
635 edits
 
(15 intermediate revisions by the same user not shown)
Line 199: Line 199:
::Description: Initialize new inserted SD Card
::Description: Initialize new inserted SD Card


=== Filesystem ===
=== FAT - Filesystem ===


:'''Show Filesystem information'''
:'''Show Filesystem information'''


:{| class="wikitable"
:{| class="wikitable"
|''fatinfo <interface> <device>''
|''<code>fatinfo <interface> <device></code>''
|}
|}


:Example: fatinfo mmc 1
:Example: <code>fatinfo mmc 1</code>


  Interface: MMC
  Interface: MMC
Line 218: Line 218:


:{| class="wikitable"
:{| class="wikitable"
|''fatls <interface> <device> <directory>''
|''<code>fatls <interface> <device> <directory></code>''
|}
|}


:Example 1: fatls mmc 1
:Example 1: <code>fatls mmc 1</code>


:Example 2: fatls mmc 1 /folder
:Example 2: <code>fatls mmc 1 /folder</code>


:'''Load Files from SD Card to SDRAM'''
:'''Load Files from SD Card to SDRAM'''


:{| class="wikitable"
:{| class="wikitable"
|''fatload <interface> <device> <SDRAM address> <directory+filename>''
|''<code>fatload <interface> <device> <SDRAM address> <directory+filename></code>''
|}
|}


:Example 1: fatload mmc 1 80100000 nk.gz
:Example 1: <code>fatload mmc 1 80100000 nk.gz</code>


:Example 2: fatload mmc 1 80100000 /folder/nk.gz
:Example 2: <code>fatload mmc 1 80100000 /folder/nk.gz</code>


=== Ethernet ===
=== Ethernet ===
Line 240: Line 240:


:{| class="wikitable"
:{| class="wikitable"
|''tftp <SDRAM address> <directory+filename>''
|''<code>tftp <SDRAM address> <directory+filename></code>''
|}
|}


:Example: tftp 80100000 nk.gz
:Example: <code>tftp 80100000 nk.gz</code>


:Example TFTP Server: "Winagents TFTP Server Manager"
:Example TFTP Server: "Winagents TFTP Server Manager"
Line 252: Line 252:


:{| class="wikitable"
:{| class="wikitable"
|''dhcp <SDRAM address> <directory+filename>''
|''<code>dhcp <SDRAM address> <directory+filename></code>''
|}
|}


:Example: dhcp 80100000 nk.gz
:Example: <code>dhcp 80100000 nk.gz</code>


:Example TFTP Server: "Winagents TFTP Server Manager"
:Example TFTP Server: "Winagents TFTP Server Manager"
Line 264: Line 264:


:{| class="wikitable"
:{| class="wikitable"
|''ping <IP address>''
|''<code>ping <IP address></code>''
|}
|}


:Example: ping 192.168.55.32
:Example: <code>ping 192.168.55.32</code>


:'''Read PHY register via MII interface'''
:'''Read PHY register via MII interface'''


:{| class="wikitable"
:{| class="wikitable"
|''mii dump <PHY address> <PHY register>''
|''<code>mii dump <PHY address> <PHY register></code>''
|}
|}


:'''DHCOM iMX25:'''
:'''DHCOM iMX25:'''


::Example: mii dump 1 0
::Example: <code>mii dump 1 0</code>


::Description: Shows PHY control register content.
::Description: Shows PHY control register content.


:'''DHCOM AM35:'''
:'''DHCOM AM35:'''
::Example: mii dump 0 0
::Example: <code>mii dump 0 0</code>


::Remark: The standard MII registers 0-5 are supported by this command. When you are working with a DHCOM AM35 module only PHY address "0" is allowed.
::Remark: The standard MII registers 0-5 are supported by this command. When you are working with a DHCOM AM35 module only PHY address "0" is allowed.
Line 291: Line 291:


:{| class="wikitable"
:{| class="wikitable"
|''printenv''
|''<code>printenv</code>''
|}
|}


Line 319: Line 319:


:{| class="wikitable"
:{| class="wikitable"
|''setenv <ENV name> <ENV value>''
|''<code>setenv <ENV name> <ENV value></code>''
|}
|}
:Example: setenv ipaddr 192.168.55.2
:Example: <code>setenv ipaddr 192.168.55.2</code>


:Note: If you need to edit "bootcmd" it is necessary to insert ";" between the unique commands. You can enter ";" at the command line with "\;".
:Note: If you need to edit "bootcmd" it is necessary to insert ";" between the unique commands. You can enter ";" at the command line with "\;".
Line 328: Line 328:


:{| class="wikitable"
:{| class="wikitable"
|''saveenv''
|''<code>saveenv</code>''
|}
|}


Line 334: Line 334:


:{| class="wikitable"
:{| class="wikitable"
|''eraseenv''
|''<code>eraseenv</code>''
|}
|}


Line 342: Line 342:


:{| class="wikitable"
:{| class="wikitable"
|''update <type> [filename]''
|''<code>update <type> [filename]</code>''
|}
|}


:Type:
:Type:


:wince = WinCE image update (default file names nk.gz or nk.bin) + ENV update
:auto = Start the automatic update with a DHupdate.ini file.


:linux = Linux image update (default file name uImage) + ENV update (default script file name uImage.env)
:wince = WinCE image update (default file names ''nk.gz'' or ''nk.bin'') + ENV update
 
:linux = Linux image update (default file name ''uImage'') + ENV update (default script file name ''uImage.env'')
:: '''Remark:'''The ENV update script must have the same filename as the linux-kernel with the ending ".env". It is possible to update the environment of u-boot without a kernel update by inserting the filename of the ENV script.
 
:rootfs = Create or replace the root-filesystem in the NAND-Flash (default file name fsroot.tar.gz). The rootfs update has to be the last item (or second to last item if you insert the reset command) in the DHupdate.ini file.
:: '''Remark:''' To run a ''"NAND-Flash root-filesystem update"'' you need a special linux-kernel which must have the filename ''"uImage.update"'' and must be available in the same diretory on your update-media as the DHupdate.ini file.


:flash = Complete flash image update
:flash = Complete flash image update
Line 358: Line 364:


:settings = Settings block update (default file name settings.bin)
:settings = Settings block update (default file name settings.bin)
:eeprom = Display-Settings block update (default file name eeprom.bin)
:reset = Execute a reset after a successfull update. A reset can only be the last item in a DHupdate.ini file.
:: '''Remark:''' Be careful with the reset command. You can easily build a endless update loop by mistake.


:'''For further information look at [[DHCOM Flash Update|DHCOM Flash Update]].'''
:'''For further information look at [[DHCOM Flash Update|DHCOM Flash Update]].'''
Line 366: Line 377:


:{| class="wikitable"
:{| class="wikitable"
|''i2c probe''
|''<code>i2c probe</code>''
|}
|}


Line 376: Line 387:


:{| class="wikitable"
:{| class="wikitable"
|''i2c md <I2C address> <start address> <end address>''
|''<code>i2c md <I2C address> <start address> <end address></code>''
|}
|}


:Example: i2c md 57 10 20
:Example: <code>i2c md 57 10 20</code>


:Description: Reads 16 Bytes from the address 0x10 to address 0x20.
:Description: Reads 16 Bytes from the address 0x10 to address 0x20.
Line 386: Line 397:


:{| class="wikitable"
:{| class="wikitable"
|''i2c mw <I2C address> <I2C register> <Value> <Bytes>''
|''<code>i2c mw <I2C address> <I2C register> <Value> <Bytes></code>''
|}
|}


:Example: i2c mw 57 0 aa 5
:Example: <code>i2c mw 57 0 aa 5</code>


:Description: Writes 0xaa to 5 Bytes from the offset 0.
:Description: Writes 0xaa to 5 Bytes from the offset 0.
Line 398: Line 409:


:{| class="wikitable"  
:{| class="wikitable"  
|''bootwince <Image address> [debug]''
|''<code>bootwince <Image address> [debug]</code>''
|}
|}


:Example: bootwince 200000
:Example: <code>bootwince 200000</code>


:Description: The address 0x20_0000 specifies NAND Flash image address. The image is loaded from NAND flash to SDRAM. Next to that u-boot starts WinCE. The "debug" option make sure that the image wouldn't be started after uncompressing.
:Description: The address 0x20_0000 specifies NAND Flash image address. The image is loaded from NAND flash to SDRAM. Next to that u-boot starts WinCE. The "debug" option make sure that the image wouldn't be started after uncompressing.
Line 408: Line 419:


:{| class="wikitable"  
:{| class="wikitable"  
|''bootwince tftp''
|''<code>bootwince tftp</code>''
|}
|}


Line 416: Line 427:


:{| class="wikitable"  
:{| class="wikitable"  
|''bootm <Kernel address> [arg]''
|''<code>bootm <Kernel address> [arg]</code>''
|}
|}


Line 424: Line 435:


:{| class="wikitable"  
:{| class="wikitable"  
|''unzip <source address> <destination address>''
|''<code>unzip <source address> <destination address></code>''
|}
|}


:Example: unzip 82900000 80100000
:Example: <code>unzip 82900000 80100000</code>


:Note: The unzip command is supporting the gzip file format.
:Note: The unzip command is supporting the gzip file format.
Line 436: Line 447:


:{| class="wikitable"  
:{| class="wikitable"  
|''bmp info <Bitmap address>''
|''<code>bmp info <Bitmap address></code>''
|}
|}


Line 446: Line 457:


:{| class="wikitable"  
:{| class="wikitable"  
|'' bmp display <Bitmap SDRAM address> [x y]''
|'' <code>bmp display <Bitmap SDRAM address> [x y]</code>''
|}
|}


Line 454: Line 465:


:{| class="wikitable"  
:{| class="wikitable"  
|''md[.b, .w, .l] <address> [count]''
|''<code>md[.b, .w, .l] <address> [count]</code>''
|}
|}


:Example: md.b 80100000 100
:Example: <code>md.b 80100000 100</code>


:'''Write'''
:'''Write'''


:{| class="wikitable"  
:{| class="wikitable"  
|''mw[.b, .w, .l] <address> <value> [count]''
|''<code> mw[.b, .w, .l] <address> <value> [count]</code>''
|}
|}


:Example: mw.b 80100000 aa 100
:Example: <code>mw.b 80100000 aa 100</code>


:Description: Writes the value 0xaa to the next 0x100 bytes from the address 0x8010_0000.  
:Description: Writes the value 0xaa to the next 0x100 bytes from the address 0x8010_0000.  
Line 472: Line 483:


:{| class="wikitable"  
:{| class="wikitable"  
|''cp[.b, .w, .l] <source> <destination> <count>''
|''<code> cp[.b, .w, .l] <source> <destination> <count></code>''
|}
|}


Line 478: Line 489:


:{| class="wikitable"  
:{| class="wikitable"  
|'' settings ''
|''<code> settings </code>''
|}
|}


Latest revision as of 13:29, 27 August 2012

NAND-Flash

Read from NAND-Flash Device
nand read <SDRAM address> <NAND Flash address> <Bytes>
Example: nand read 80000000 400000 b40000
Description: Copies 11,25MByte from NAND Flash address 0x40_0000 to SDRAM address 0x8000_0000
Erase NAND-Flash blocks
nand erase <Block base address> <Bytes>
Example: nand erase 400000 40000
Description: Deletes NAND Flash content from address 0x40_0000 to 0x43_FFFF
Note: The Bytes information needs to be block size aligned!
Write to NAND-Flash Device
nand write <SDRAM address> <NAND-Flash address> <Bytes>
Example: nand write 80000000 400000 b40000
Description: Copies 11,25MByte from SDRAM address 0x8000_0000 to NAND Flash address 0x40_0000
Note: The Bytes information needs to be page size aligned!
Show bad NAND-Flash blocks
nand bad
Description: Shows the bad NAND-Flash blocks.
Show NAND-Flash content
nand dump <NAND-Flash address>
Example: nand dump 400000
Description: Shows the content of the specified NAND-Flash block

SPI Flash

Only available at iMX25

SPI Flash Init
sf probe <bus:cs> [frequency]
Example: sf probe 0:1
Description: Initializes the OnBoard SPI Flash
SPI Flash Read
sf read <SDRAM address> <SPI Flash address> <Bytes>
Example: sf read 80000000 40000 10000
Description: Copies 64kByte from SPI Flash address 0x4_0000 to SDRAM address 0x8000_0000
SPI Flash Write
sf write <SDRAM address> <SPI Flash address> <Bytes>
Example: sf write 80000000 40000 10000
Description: Copies 64kByte from SDRAM address 0x8000_0000 to SPI Flash address 0x4_0000
SPI Flash Erase
sf erase <SPI Flash address> <Bytes>
Example: sf erase 40000 10000
Description: Deletes SPI Flash content from address 0x4_0000 to 0x4_FFFF
Note: The Bytes information needs to be sector size aligned!

LCD contoller

Show LCD controller settings
lcdinfo
Example output:
 Display Resolution: 800 x 480 pixels
 Display Type:       Active Color Display
 Pixel Clock:        22 MHz
 Bits per Pixel:     16 Bits/Pixel
 Pixel Polarity:     Active High
 VSYNC Polarity:     Active Low
 HSYNC Polarity:     Active Low
 Clock Polarity:     Pos. Edge
 Output En Polarity: Active High
 HSYNC Puls Width:   64 Clock Cycles
 HSYNC Back Porch:   86 Clock Cycles
 HSYNC Front Porch:  42 Clock Cycles
 VSYNC Puls Width:   2 Line Cycles
 VSYNC Back Porch:   33 Line Cycles
 VSYNC Front Porch:  10 Line Cycles

GPIO's

Show DHCOM GPIO settings
gpioinfo
Example output:
 GPIO_A: Direction = Input
         State     = 0
 GPIO_B: Direction = Input
         State     = 0
 GPIO_C: Direction = Input
         State     = 0
 GPIO_D: Direction = Input
         State     = 0
 GPIO_E: Direction = Input
         State     = 1
 GPIO_F: Direction = Input
         State     = 1
 GPIO_G: Direction = Output
         State     = 1
 GPIO_H: Direction = Input
         State     = 1
 GPIO_I: Direction = Input
         State     = 1
 GPIO_J: Direction = Input
         State     = 1
 GPIO_K: Direction = Input
         State     = 0

SD/MMC Card

DHCOM iMX25:
Switch between MicroSD and SD Slot
mmcswitch <Slot number>
Example: mmcswitch 2
Description: Switch between SD/MMC Slots: 1 --> SD/MMC Slot, 2 --> MicroSD Slot
Initialize SD/MMC Card
mmcinit
Description: Initialize new inserted SD Card


DHCOM AM35:
Switch between onboard microSD Slot and external SD - Card interface
mmc switch <Slot number>
Example: mmc switch 2
Description: available interfaces
  • 1 --> external SD/MMC Slot
  • 2 --> onboard microSD Slot
Initialize SD/MMC Card
mmc init
Description: Initialize new inserted SD Card

FAT - Filesystem

Show Filesystem information
fatinfo <interface> <device>
Example: fatinfo mmc 1
Interface: MMC
 Device 1: Vendor: Man 094150 Snr 266e068c Rev: 1.0 Prod: AF UD
           Type: Removable Hard Disk
           Capacity: 121.2 MB = 0.1 GB (248320 x 512)
 Partition 1: Filesystem: FAT16 "NO NAME    "
List files
fatls <interface> <device> <directory>
Example 1: fatls mmc 1
Example 2: fatls mmc 1 /folder
Load Files from SD Card to SDRAM
fatload <interface> <device> <SDRAM address> <directory+filename>
Example 1: fatload mmc 1 80100000 nk.gz
Example 2: fatload mmc 1 80100000 /folder/nk.gz

Ethernet

Load File via TFTP to SDRAM
tftp <SDRAM address> <directory+filename>
Example: tftp 80100000 nk.gz
Example TFTP Server: "Winagents TFTP Server Manager"
Note: For TFTP download it is necessary to config the ENV variables "ipaddr" and "serverip"
Load File via TFTP to SDRAM using DHCP
dhcp <SDRAM address> <directory+filename>
Example: dhcp 80100000 nk.gz
Example TFTP Server: "Winagents TFTP Server Manager"
Note: It is necessary to config the ENV variable "serverip" with the ip-address of your TFTP-Server
Ping
ping <IP address>
Example: ping 192.168.55.32
Read PHY register via MII interface
mii dump <PHY address> <PHY register>
DHCOM iMX25:
Example: mii dump 1 0
Description: Shows PHY control register content.
DHCOM AM35:
Example: mii dump 0 0
Remark: The standard MII registers 0-5 are supported by this command. When you are working with a DHCOM AM35 module only PHY address "0" is allowed.

Environment

Show ENV variables
printenv 
bootdelay=0
baudrate=38400
ipaddr=192.168.55.230
serverip=192.168.55.36
gatewayip=192.168.55.36
netmask=255.255.255.0
frias=5
kernel=uImage
bootargs=console=ttymxc0,115200 root=/dev/mmcblk0p2
nandbootwince=update;bootwince 00200000
splashimage=0x000c0000
save_ENV_to_flash=setenv ENVinFlash 1; saveenv
ENVinFlash=1
ethaddr=00:04:a3:34:b6:0d
ethact=FEC0
winceimagetype=nk.gz
winceimagesize=00ba55ee
loadaddr=00200000
bootcmd=run nandbootwince
filesize=212050
Environment size: 449/262140 bytes
Set ENV variables
setenv <ENV name> <ENV value>
Example: setenv ipaddr 192.168.55.2
Note: If you need to edit "bootcmd" it is necessary to insert ";" between the unique commands. You can enter ";" at the command line with "\;".
Save ENV variables
saveenv
Erase all ENV variables
eraseenv
Note: It is necessary to restart the system after "eraseenv", to restore the default ENV settings.

Update

update <type> [filename]
Type:
auto = Start the automatic update with a DHupdate.ini file.
wince = WinCE image update (default file names nk.gz or nk.bin) + ENV update
linux = Linux image update (default file name uImage) + ENV update (default script file name uImage.env)
Remark:The ENV update script must have the same filename as the linux-kernel with the ending ".env". It is possible to update the environment of u-boot without a kernel update by inserting the filename of the ENV script.
rootfs = Create or replace the root-filesystem in the NAND-Flash (default file name fsroot.tar.gz). The rootfs update has to be the last item (or second to last item if you insert the reset command) in the DHupdate.ini file.
Remark: To run a "NAND-Flash root-filesystem update" you need a special linux-kernel which must have the filename "uImage.update" and must be available in the same diretory on your update-media as the DHupdate.ini file.
flash = Complete flash image update
bootloader = Bootloader update (default file name u-boot.bin)
splash = Bootbitmap update (default file name splash.bmp)
settings = Settings block update (default file name settings.bin)
eeprom = Display-Settings block update (default file name eeprom.bin)
reset = Execute a reset after a successfull update. A reset can only be the last item in a DHupdate.ini file.
Remark: Be careful with the reset command. You can easily build a endless update loop by mistake.
For further information look at DHCOM Flash Update.

I2C

List available devices
i2c probe 
Valid chip addresses: 00 57 6F
0x5F = DHCOM i.MX25 Core Module EEPROM
0x6F = DHCOM i.MX25 Core Module Real Time Clock
Read
i2c md <I2C address> <start address> <end address>
Example: i2c md 57 10 20
Description: Reads 16 Bytes from the address 0x10 to address 0x20.
Write
i2c mw <I2C address> <I2C register> <Value> <Bytes>
Example: i2c mw 57 0 aa 5
Description: Writes 0xaa to 5 Bytes from the offset 0.

OS Boot

WinCE
bootwince <Image address> [debug]
Example: bootwince 200000
Description: The address 0x20_0000 specifies NAND Flash image address. The image is loaded from NAND flash to SDRAM. Next to that u-boot starts WinCE. The "debug" option make sure that the image wouldn't be started after uncompressing.
Note: The Image address could also be an SDRAM address. But it is necessary to copy the Image (via tftp or nand flash commands) to the SDRAM before calling "bootwince".
bootwince tftp
Note: The ENV variables "loadaddr" and "bootfile" needs to be set before calling the command. For *.gz image types the "loadaddr" should be set to 0x8290_0000 and for *.bin images the address should be 0x8100_0000.
Linux
bootm <Kernel address> [arg]
Note: When booting a Linux kernel,‘arg' can be the address of an initrd image.

Unzip

unzip <source address> <destination address>
Example: unzip 82900000 80100000
Note: The unzip command is supporting the gzip file format.

Bitmap

Information
bmp info <Bitmap address> 
Image size    : 800 x 480
Bits per pixel: 8
Compression   : 0
Display
bmp display <Bitmap SDRAM address> [x y]

Memory

Display
md[.b, .w, .l] <address> [count]
Example: md.b 80100000 100
Write
mw[.b, .w, .l] <address> <value> [count]
Example: mw.b 80100000 aa 100
Description: Writes the value 0xaa to the next 0x100 bytes from the address 0x8010_0000.
Copy
cp[.b, .w, .l] <source> <destination> <count>

Show DHCOM Settings

settings
Example:
 VALIDATION_ID:    "DH"
 DISPLAY_ID:       0x00
 LENGTH:           0x2c
 X_RESOLUTION:     800 pixel
 Y_RESOLUTION:     480 pixel
 PIXEL_CLOCK:      22200 kHz
 LCD_CONFIG_FLAGS: 0x3e3
 HSW:              64 pixel clocks
 VSW:              2 line clocks
 HFP:              42 pixel clocks
 HBP:              86 pixel clocks
 VFP:              10 line clocks
 VBP:              33 line clocks
 DATALINES:        16
 ACB:              0
 ACBI:             0
 GPIO_DIR:         0x01ff
 GPIO_STATE:       0x0000
 HW_CONFIG_FLAGS:  0x001e
Retrieved from "https://wiki.dh-electronics.com/index.php?title=Template:TemplateUbootCommands&oldid=824"