U-boot console commands: Difference between revisions

From Wiki-DB
Jump to navigationJump to search
← Older editNewer edit →
Lzenz (talk | contribs)
635 edits
Blanked the page
Lzenz (talk | contribs)
635 edits
No edit summary
Line 1: Line 1:
== NAND Flash ==


:'''Nand Flash Read'''
:''nand read <SDRAM address> <NAND Flash address> <Bytes>''
:Example: nand read 80000000 400000 b40000
:Description: Copies 11,25MByte from NAND Flash address 0x40_0000 to SDRAM address 0x8000_0000
:'''Nand Flash Erase'''
:''nand erase <Block base address> <Bytes>''
:Example: nand erase 400000 40000
:Description: Deletes NAND Flash content from address 0x40_0000 to 0x43_FFFF
:Note: The Bytes information needs to be block size aligned!
:'''Nand Flash Write'''
:''nand write <SDRAM address> <NAND Flash address> <Bytes>''
:Example: nand write 80000000 400000 b40000
:Description: Cpoies 11,25MByte from SDRAM address 0x8000_0000 to NAND Flash address 0x40_0000
:Note: The Bytes information needs to be page size aligned!
:'''Show bad NAND Flash blocks'''
:''nand bad''
:Description: Shows the bad NAND Flash blocks.
:'''Show NAND FLash content'''
:''nand dump <NAND Flash address>''
:Example: nand dump 400000
:Description: Shows the content of the specified NAND Flash block
== SPI Flash ==
:'''SPI Flash Init'''
:''sf probe <bus:cs> [frequency]''
:Example: sf probe 0:1
:Description: Initializes the OnBoard SPI Flash
:'''SPI Flash Read'''
:''sf read <SDRAM address> <SPI Flash address> <Bytes>''
:Example: sf read 80000000 40000 10000
:Description: Copies 64kByte from SPI Flash address 0x4_0000 to SDRAM address 0x8000_0000
:'''SPI Flash Write'''
:''sf write <SDRAM address> <SPI Flash address> <Bytes>''
:Example: sf write 80000000 40000 10000
:Description: Copies 64kByte from SDRAM address 0x8000_0000 to SPI Flash address 0x4_0000
:'''SPI Flash Erase'''
:''sf erase <SPI Flash address> <Bytes>''
:Example: sf erase 40000 10000
:Description: Deletes SPI Flash content from address 0x4_0000 to 0x4_FFFF
:Note: The Bytes information needs to be sector size aligned!
== LCD contoller ==
:'''Show LCD controller settings'''
:''lcdinfo''
:Example: 
  Display Resolution: 800 x 480 pixels
  Display Type:      Active Color Display
  Pixel Clock:        22 MHz
  Bits per Pixel:    16 Bits/Pixel
  Pixel Polarity:    Active High
  VSYNC Polarity:    Active Low
  HSYNC Polarity:    Active Low
  Clock Polarity:    Pos. Edge
  Output En Polarity: Active High
  HSYNC Puls Width:  64 Clock Cycles
  HSYNC Back Porch:  86 Clock Cycles
  HSYNC Front Porch:  42 Clock Cycles
  VSYNC Puls Width:  2 Line Cycles
  VSYNC Back Porch:  33 Line Cycles
  VSYNC Front Porch:  10 Line Cycles
== GPIO's ==
:'''Show DHCOM GPIO settings'''
:''gpioinfo''
:Example:
  GPIO_A: Direction = Input
          State    = 0
  GPIO_B: Direction = Input
          State    = 0
  GPIO_C: Direction = Input
          State    = 0
  GPIO_D: Direction = Input
          State    = 0
  GPIO_E: Direction = Input
          State    = 1
  GPIO_F: Direction = Input
          State    = 1
  GPIO_G: Direction = Output
          State    = 1
  GPIO_H: Direction = Input
          State    = 1
  GPIO_I: Direction = Input
          State    = 1
  GPIO_J: Direction = Input
          State    = 1
  GPIO_K: Direction = Input
          State    = 0
== SD/MMC Card ==
:'''Switch between MicroSD and SD Slot'''
:''mmcswitch <Slot number>''
:Example: mmcswitch 2
:Description: Switch between SD/MMC Slots: 1 --> SD/MMC Slot, 2 --> MicroSD Slot
:'''Initialize SD/MMC Card'''
:''mmcinit''
:Description: Initialize new inserted SD Card
== Filesystem ==
:'''Show Filesystem information'''
:''fatinfo <interface> <device>''
:Example: fatinfo mmc 1
Interface: MMC
  Device 1: Vendor: Man 094150 Snr 266e068c Rev: 1.0 Prod: AF UD
            Type: Removable Hard Disk
            Capacity: 121.2 MB = 0.1 GB (248320 x 512)
  Partition 1: Filesystem: FAT16 "NO NAME    "
:'''List files'''
:''fatls <interface> <device> <directory>''
:Example 1: fatls mmc 1
:Example 2: fatls mmc 1 /folder
:'''Load Files from SD Card to SDRAM'''
:''fatload <interface> <device> <SDRAM address> <directory+filename>''
:Example 1: fatload mmc 1 80100000 nk.gz
:Example 2: fatload mmc 1 80100000 /folder/nk.gz
== Ethernet ==
:'''Load File via TFTP to SDRAM'''
:''tftp <SDRAM address> <directory+filename>''
:Example: tftp 80100000 nk.gz
:Example TFTP Server: "Winagents TFTP Server Manager"
:Note: For TFTP download it is necessary to config the ENV variables "ipaddr" and "serverip"
:'''Ping'''
:''ping <IP address>''
:Example: ping 192.168.55.32
:'''Read PHY register via MII interface'''
:''mii dump <PHY address> <PHY register>''
:Example: mii dump 1 0
:Description: Shows PHY control register content.
== Environment ==
:'''Show ENV variables'''
:''printenv''
bootdelay=0
baudrate=38400
ipaddr=192.168.55.230
serverip=192.168.55.36
gatewayip=192.168.55.36
netmask=255.255.255.0
frias=5
kernel=uImage
bootargs=console=ttymxc0,115200 root=/dev/mmcblk0p2
nandbootwince=update;bootwince 00200000
splashimage=0x000c0000
save_ENV_to_flash=setenv ENVinFlash 1; saveenv
ENVinFlash=1
ethaddr=00:04:a3:34:b6:0d
ethact=FEC0
winceimagetype=nk.gz
winceimagesize=00ba55ee
loadaddr=00200000
bootcmd=run nandbootwince
filesize=212050
Environment size: 449/262140 bytes
:'''Set ENV variables'''
:''setenv <ENV name> <ENV value>''
:Example: setenv ipaddr 192.168.55.2
:Note: If you need to edit "bootcmd" it is necessary to insert ";" between the unique commands. You can enter ";" at the command line with "\;".
:'''Save ENV variables'''
:''saveenv''
:'''Erase all ENV variables'''
:''eraseenv''
:Note: It is necessary to restart the system after "eraseenv", to restore the default ENV settings.
== Update ==
:Note: See also Bootloader subitem Flash Update.
:'''iMX25_update.bmp file'''
:''update''
:Description: Starts Flash update with "iMX25_update.bmp" file.
:'''Command line'''
:''update <type> [filename]''
:Type:
:wince = WinCE image update (default file names nk.gz or nk.bin) + ENV update
:linux = Linux image update (default file name uImage) + ENV update (default script file name uImage.env)
:flash = Complete flash image update
:bootloader = Bootloader update (default file name u-boot.bin)
:splash = Bootbitmap update (default file name splash.bmp)
:settings = Settings block update (default file name settings.bin)
== I2C ==
:'''List available devices'''
:''i2c probe''
Valid chip addresses: 00 57 6F
0x5F = DHCOM i.MX25 Core Module EEPROM
0x6F = DHCOM i.MX25 Core Module Real Time Clock
:'''Read'''
:''i2c md <I2C address> <start address> <end address>''
:Example: i2c md 57 10 20
:Description: Reads 16 Bytes from the address 0x10 to address 0x20.
:'''Write'''
:''i2c mw <I2C address> <I2C register> <Value> <Bytes>''
:Example: i2c mw 57 0 aa 5
:Description: Writes 0xaa to 5 Bytes from the offset 0.
== OS Boot ==
:'''WinCE'''
:''bootwince <Image address> [debug]''
:Example: bootwince 200000
:Description: The address 0x20_0000 specifies NAND Flash image address. The image is loaded from NAND flash to SDRAM. Next to that u-boot starts WinCE. The "debug" option make sure that the image wouldn't be started after uncompressing.
:Note: The Image address could also be an SDRAM address. But it is necessary to copy the Image (via tftp or nand flash commands) to the SDRAM before calling "bootwince".
:''bootwince tftp''
:Note: The ENV variables "loadaddr" and "bootfile" needs to be set before calling the command. For *.gz image types the "loadaddr" should be set to 0x8290_0000 and for *.bin images the address should be 0x8100_0000.
:'''Linux'''
:''bootm <Kernel address> [arg]''
:Note: When booting a Linux kernel,‘arg' can be the address of an initrd image.
== Unzip ==
:''unzip <source address> <destination address>''
:Example: unzip 82900000 80100000
:Note: The unzip command is supporting the gzip file format.
== Bitmap ==
:'''Information'''
:''bmp info <Bitmap address>''
Image size    : 800 x 480
Bits per pixel: 8
Compression  : 0
:'''Display'''
:'' bmp display <Bitmap SDRAM address> [x y]''
== Memory ==
:'''Display'''
:''md[.b, .w, .l] <address> [count]''
:Example: md.b 80100000 100
:'''Write'''
:''mw[.b, .w, .l] <address> <value> [count]''
:Example: mw.b 80100000 aa 100
:Description: Writes the value 0xaa to the next 0x100 bytes from the address 0x8010_0000.
:'''Copy'''
:''cp[.b, .w, .l] <source> <destination> <count>''
== Show DHCOM Settings ==
:''settings''
:Example: 
  VALIDATION_ID:    "DH"
  DISPLAY_ID:      0x00
  LENGTH:          0x2c
  X_RESOLUTION:    800 pixel
  Y_RESOLUTION:    480 pixel
  PIXEL_CLOCK:      22200 kHz
  LCD_CONFIG_FLAGS: 0x3e3
  HSW:              64 pixel clocks
  VSW:              2 line clocks
  HFP:              42 pixel clocks
  HBP:              86 pixel clocks
  VFP:              10 line clocks
  VBP:              33 line clocks
  DATALINES:        16
  ACB:              0
  ACBI:            0
  GPIO_DIR:        0x01ff
  GPIO_STATE:      0x0000
  HW_CONFIG_FLAGS:  0x001e

Revision as of 14:54, 8 May 2012

NAND Flash

Nand Flash Read
nand read <SDRAM address> <NAND Flash address> <Bytes>
Example: nand read 80000000 400000 b40000
Description: Copies 11,25MByte from NAND Flash address 0x40_0000 to SDRAM address 0x8000_0000
Nand Flash Erase
nand erase <Block base address> <Bytes>
Example: nand erase 400000 40000
Description: Deletes NAND Flash content from address 0x40_0000 to 0x43_FFFF
Note: The Bytes information needs to be block size aligned!
Nand Flash Write
nand write <SDRAM address> <NAND Flash address> <Bytes>
Example: nand write 80000000 400000 b40000
Description: Cpoies 11,25MByte from SDRAM address 0x8000_0000 to NAND Flash address 0x40_0000
Note: The Bytes information needs to be page size aligned!
Show bad NAND Flash blocks
nand bad
Description: Shows the bad NAND Flash blocks.
Show NAND FLash content
nand dump <NAND Flash address>
Example: nand dump 400000
Description: Shows the content of the specified NAND Flash block

SPI Flash

SPI Flash Init
sf probe <bus:cs> [frequency]
Example: sf probe 0:1
Description: Initializes the OnBoard SPI Flash
SPI Flash Read
sf read <SDRAM address> <SPI Flash address> <Bytes>
Example: sf read 80000000 40000 10000
Description: Copies 64kByte from SPI Flash address 0x4_0000 to SDRAM address 0x8000_0000
SPI Flash Write
sf write <SDRAM address> <SPI Flash address> <Bytes>
Example: sf write 80000000 40000 10000
Description: Copies 64kByte from SDRAM address 0x8000_0000 to SPI Flash address 0x4_0000
SPI Flash Erase
sf erase <SPI Flash address> <Bytes>
Example: sf erase 40000 10000
Description: Deletes SPI Flash content from address 0x4_0000 to 0x4_FFFF
Note: The Bytes information needs to be sector size aligned!

LCD contoller

Show LCD controller settings
lcdinfo
Example:
 Display Resolution: 800 x 480 pixels
 Display Type:       Active Color Display
 Pixel Clock:        22 MHz
 Bits per Pixel:     16 Bits/Pixel
 Pixel Polarity:     Active High
 VSYNC Polarity:     Active Low
 HSYNC Polarity:     Active Low
 Clock Polarity:     Pos. Edge
 Output En Polarity: Active High
 HSYNC Puls Width:   64 Clock Cycles
 HSYNC Back Porch:   86 Clock Cycles
 HSYNC Front Porch:  42 Clock Cycles
 VSYNC Puls Width:   2 Line Cycles
 VSYNC Back Porch:   33 Line Cycles
 VSYNC Front Porch:  10 Line Cycles

GPIO's

Show DHCOM GPIO settings
gpioinfo
Example:
 GPIO_A: Direction = Input
         State     = 0
 GPIO_B: Direction = Input
         State     = 0
 GPIO_C: Direction = Input
         State     = 0
 GPIO_D: Direction = Input
         State     = 0
 GPIO_E: Direction = Input
         State     = 1
 GPIO_F: Direction = Input
         State     = 1
 GPIO_G: Direction = Output
         State     = 1
 GPIO_H: Direction = Input
         State     = 1
 GPIO_I: Direction = Input
         State     = 1
 GPIO_J: Direction = Input
         State     = 1
 GPIO_K: Direction = Input
         State     = 0

SD/MMC Card

Switch between MicroSD and SD Slot
mmcswitch <Slot number>
Example: mmcswitch 2
Description: Switch between SD/MMC Slots: 1 --> SD/MMC Slot, 2 --> MicroSD Slot
Initialize SD/MMC Card
mmcinit
Description: Initialize new inserted SD Card

Filesystem

Show Filesystem information
fatinfo <interface> <device>
Example: fatinfo mmc 1
Interface: MMC
 Device 1: Vendor: Man 094150 Snr 266e068c Rev: 1.0 Prod: AF UD
           Type: Removable Hard Disk
           Capacity: 121.2 MB = 0.1 GB (248320 x 512)
 Partition 1: Filesystem: FAT16 "NO NAME    "
List files
fatls <interface> <device> <directory>
Example 1: fatls mmc 1
Example 2: fatls mmc 1 /folder
Load Files from SD Card to SDRAM
fatload <interface> <device> <SDRAM address> <directory+filename>
Example 1: fatload mmc 1 80100000 nk.gz
Example 2: fatload mmc 1 80100000 /folder/nk.gz

Ethernet

Load File via TFTP to SDRAM
tftp <SDRAM address> <directory+filename>
Example: tftp 80100000 nk.gz
Example TFTP Server: "Winagents TFTP Server Manager"
Note: For TFTP download it is necessary to config the ENV variables "ipaddr" and "serverip"
Ping
ping <IP address>
Example: ping 192.168.55.32
Read PHY register via MII interface
mii dump <PHY address> <PHY register>
Example: mii dump 1 0
Description: Shows PHY control register content.

Environment

Show ENV variables
printenv
bootdelay=0
baudrate=38400
ipaddr=192.168.55.230
serverip=192.168.55.36
gatewayip=192.168.55.36
netmask=255.255.255.0
frias=5
kernel=uImage
bootargs=console=ttymxc0,115200 root=/dev/mmcblk0p2
nandbootwince=update;bootwince 00200000
splashimage=0x000c0000
save_ENV_to_flash=setenv ENVinFlash 1; saveenv
ENVinFlash=1
ethaddr=00:04:a3:34:b6:0d
ethact=FEC0
winceimagetype=nk.gz
winceimagesize=00ba55ee
loadaddr=00200000
bootcmd=run nandbootwince
filesize=212050
Environment size: 449/262140 bytes
Set ENV variables
setenv <ENV name> <ENV value>
Example: setenv ipaddr 192.168.55.2
Note: If you need to edit "bootcmd" it is necessary to insert ";" between the unique commands. You can enter ";" at the command line with "\;".
Save ENV variables
saveenv
Erase all ENV variables
eraseenv
Note: It is necessary to restart the system after "eraseenv", to restore the default ENV settings.

Update

Note: See also Bootloader subitem Flash Update.
iMX25_update.bmp file
update
Description: Starts Flash update with "iMX25_update.bmp" file.
Command line
update <type> [filename]
Type:
wince = WinCE image update (default file names nk.gz or nk.bin) + ENV update
linux = Linux image update (default file name uImage) + ENV update (default script file name uImage.env)
flash = Complete flash image update
bootloader = Bootloader update (default file name u-boot.bin)
splash = Bootbitmap update (default file name splash.bmp)
settings = Settings block update (default file name settings.bin)

I2C

List available devices
i2c probe
Valid chip addresses: 00 57 6F
0x5F = DHCOM i.MX25 Core Module EEPROM
0x6F = DHCOM i.MX25 Core Module Real Time Clock
Read
i2c md <I2C address> <start address> <end address>
Example: i2c md 57 10 20
Description: Reads 16 Bytes from the address 0x10 to address 0x20.
Write
i2c mw <I2C address> <I2C register> <Value> <Bytes>
Example: i2c mw 57 0 aa 5
Description: Writes 0xaa to 5 Bytes from the offset 0.

OS Boot

WinCE
bootwince <Image address> [debug]
Example: bootwince 200000
Description: The address 0x20_0000 specifies NAND Flash image address. The image is loaded from NAND flash to SDRAM. Next to that u-boot starts WinCE. The "debug" option make sure that the image wouldn't be started after uncompressing.
Note: The Image address could also be an SDRAM address. But it is necessary to copy the Image (via tftp or nand flash commands) to the SDRAM before calling "bootwince".
bootwince tftp
Note: The ENV variables "loadaddr" and "bootfile" needs to be set before calling the command. For *.gz image types the "loadaddr" should be set to 0x8290_0000 and for *.bin images the address should be 0x8100_0000.
Linux
bootm <Kernel address> [arg]
Note: When booting a Linux kernel,‘arg' can be the address of an initrd image.

Unzip

unzip <source address> <destination address>
Example: unzip 82900000 80100000
Note: The unzip command is supporting the gzip file format.

Bitmap

Information
bmp info <Bitmap address>
Image size    : 800 x 480
Bits per pixel: 8
Compression   : 0
Display
bmp display <Bitmap SDRAM address> [x y]

Memory

Display
md[.b, .w, .l] <address> [count]
Example: md.b 80100000 100
Write
mw[.b, .w, .l] <address> <value> [count]
Example: mw.b 80100000 aa 100
Description: Writes the value 0xaa to the next 0x100 bytes from the address 0x8010_0000.
Copy
cp[.b, .w, .l] <source> <destination> <count>

Show DHCOM Settings

settings
Example:
 VALIDATION_ID:    "DH"
 DISPLAY_ID:       0x00
 LENGTH:           0x2c
 X_RESOLUTION:     800 pixel
 Y_RESOLUTION:     480 pixel
 PIXEL_CLOCK:      22200 kHz
 LCD_CONFIG_FLAGS: 0x3e3
 HSW:              64 pixel clocks
 VSW:              2 line clocks
 HFP:              42 pixel clocks
 HBP:              86 pixel clocks
 VFP:              10 line clocks
 VBP:              33 line clocks
 DATALINES:        16
 ACB:              0
 ACBI:             0
 GPIO_DIR:         0x01ff
 GPIO_STATE:       0x0000
 HW_CONFIG_FLAGS:  0x001e
Retrieved from "https://wiki.dh-electronics.com/index.php?title=U-boot_console_commands&oldid=491"