DHCOM iMX6ULL-D2: Difference between revisions

Revision as of 16:31, 3 March 2020


Contents 1 Hardware 2 Software Support 3 BSP Sources 3.1 U-Boot 3.2 Linux Kernel 4 Download binaries/images 4.1 U-Boot (for eMMC COMs) 4.2 Update Kernel 4.3 Debian based images


Cortex-A7 NXP i.MX6ULL up to 900 MHz 128 - 1024 MByte NAND flash memory (8 bit bus width) or 4 - 16 GByte eMMC flash (8 bit bus width) 2 MB SPI boot flash 128 - 1024 MByte DDR3-400 On module microSD card socket (4 bit SDIO) ^[1] LC display controller, 18 bit colors, 1366x768 pixels On-chip touch controller for 4-wire resistive touch screens 2x Ethernet controller 10/100 Mbit, IEEE1588 conform ^[2] USB 2.0 OTG high-speed USB 2.0 host high speed 2x Standard UART with hardware handshake support ^[3]^[4] WiFi iEEE802.11b/g/n + Bluetooth v4.1 (BR/EDR/BLE) module on BGA ^[1]^[4] ^[1] On module microSD card socket is only available if WiFi is not mounted. ^[2] The second SPI is only available, if the second ethernet is not mounted. ^[3] CTS and RTS of the first UART is only available if second CAN port is not connected. ^[4] The second UART is only available if Bluetooth is not used. This means WiFi/BT module 1DX is not mounted or module 1FX (only WiFi) is mounted. ^[5] I²S lines are shared with JTAG.	2x CAN interface ^[3] 2x SPI interface ^[2] 2x I²C interface I²S Audio codec (1 x microphone, 1 x Line in, 1x Line out) ^[5] Real-time clock (I²C connection), low power temperature compensated 2x 10 bit analog input (I²C connection) 2x 256 Bytes EEPROM with integrated MAC address PWM channel 22 GPIOs (A-U + INT_HI_PRIO) JTAG debug connection via FFC plug connector Industrial temperature range (-40°C to +85°C) SODIMM-200 socket with DHCOM pin assignment

More on how to program it with the U-Boot command "update bootloader ..." on the page "DHCOM Update Mechanism"

More on how to use it on the page "DHCOM Update Mechanism"

Hint: Open it with Disks by double click on Debian Linux. Use balenaEtcher on Windows.

Extract the files on a USB stick (MBR / FAT32) and insert it into your board / device. More about the files on the page "DHCOM Update Mechanism"

@@ Line 77: / Line 77: @@
 :* [https://www.dropbox.com/s/3c3y5v3kchowvhf/HD00051_2020-03-03_imx6ull_jessie_sdcard_2000MB.img.xz?raw=1 2GB SD card image (xz compressed)]
-:: Hint: Open it with Disks by double click on Linux. Use [https://www.balena.io/etcher balenaEtcher] on Windows.
+:: Hint: Open it with Disks by double click on Debian Linux. Use [https://www.balena.io/etcher balenaEtcher] on Windows.
-:* [https://www.dropbox.com/s/i9vecx0pfpis7yv/HD00051_2020-03-03_imx6ull_jessie_USB_stick_update.zip?raw=1 USB stick update image]
+:* [https://www.dropbox.com/s/i9vecx0pfpis7yv/HD00051_2020-03-03_imx6ull_jessie_USB_stick_update.zip?raw=1 USB stick update image (for eMMC)]
 :: Extract the files on a USB stick (MBR / FAT32) and insert it into your board / device. More about the files on the page [[DHCOM Update Mechanism|"DHCOM Update Mechanism"]]