DHSBC STM32MP13 DFU and UMS usage: Difference between revisions

From Wiki-DB
Jump to navigationJump to search
← Older editNewer edit →
Ageisreiter (talk | contribs)
1,202 edits
Ageisreiter (talk | contribs)
1,202 edits
Line 27: Line 27:
  ||USB (DFU)||<tt>000b</tt>
  ||USB (DFU)||<tt>000b</tt>
  |-
  |-
  ||SPI Flash ||<tt>011b</tt>
  ||SPI Flash ||<tt>001b</tt>
  |}
  |}
'''NOTE:''' First Board bevision 719-100 ON means 0!
'''NOTE:''' First Board revision 719-100 -> ON means 0 -> bit 1 = OFF, bit 2,3 = ON!


=== Install dfu-util (debian) ===
=== Install dfu-util (debian) ===

Revision as of 16:51, 5 August 2024


To recover a corrupted U-Boot on a STM32MP1-based DHCOM, we can use the default fallback boot source DFU via serial link or USB to temporarily boot U-Boot SPL and U-Boot. From this U-Boot shell we can write both bootloader images from the SD card to the boot flash.

Requirements

Software

Hardware

  • DHSBC STM32MP13 board
  • USB-A to Type-C cable (for DFU and UMS data connection)
  • Type-C power supply for DHCBS STM32Mp13 board
  • FTDI cable TTL-232R-3V3 for console connection

Preparation

This installation was made on the Virtual Machine for Application Development. All console expressions refer to this Debian system, but any other debian based system should also work.

BOOT MODES

USB (DFU) 000b
SPI Flash 001b

NOTE: First Board revision 719-100 -> ON means 0 -> bit 1 = OFF, bit 2,3 = ON!

Install dfu-util (debian)

apt-get install dfu-util

Collect artifacts from OE build:

  • tf-a-stm32mp135f-dhcor-dhsbc.stm32-stm32mp1
  • fip.bin-stm32mp1
  • *image*.wic

Start U-Boot via USB DFU upload:

$ dfu-util -a 0 -D tf-a-stm32mp135f-dhcor-dhsbc.stm32 -R
$ dfu-util -a 0 -D fip.bin -R

Install bootloader to SPI NOR:

  • U-Boot side:
=> sf probe
=> env set dfu_alt_info "mtd nor0=fsbl1 raw 0x0 0x40000;fsbl2 raw 0x40000 0x40000;uboot raw 0x80000 0x160000;env1 raw 0x3e0000 0x10000;env2 raw 0x3f0000 0x10000"
=> dfu 0 mtd
  • Host PC side
$ dfu-util -a 2 -D fip.bin
$ dfu-util -a 1 -D tf-a-stm32mp135f-dhcor-dhsbc.stm32
$ dfu-util -a 0 -D tf-a-stm32mp135f-dhcor-dhsbc.stm32

Power off the board, switch boot mode to 123=OFF-ON-ON (QSPI NOR boot)

Reset Environment to default of new bootloader

=> env default -a
=> saveenv
=> saveenv

Install root filesystem to eMMC:

  • U-Boot side:
=> ums 0 mmc 0
  • Host PC side
$ dd if=*image*wic of=/dev/sdX bs=4M

Power off the board, switch boot mode to 123=OFF-ON-ON (QSPI NOR boot)

Power on and boot

Retrieved from "https://wiki.dh-electronics.com/index.php?title=DHSBC_STM32MP13_DFU_and_UMS_usage&oldid=3902"