DHCOM iMX25-D2

Bootloader U-Boot

Console commands

NAND Flash

Nand Flash Read

nand read <SDRAM address> <NAND Flash address> <Bytes>

Example: nand read 80000000 400000 b40000

Description: Copies 11,25MByte from NAND Flash address 0x40_0000 to SDRAM address 0x8000_0000

Nand Flash Erase

nand erase <Block base address> <Bytes>

Example: nand erase 400000 40000

Description: Deletes NAND Flash content from address 0x40_0000 to 0x43_FFFF

Note: The Bytes information needs to be block size aligned!

Nand Flash Write

nand write <SDRAM address> <NAND Flash address> <Bytes>

Example: nand write 80000000 400000 b40000

Description: Cpoies 11,25MByte from SDRAM address 0x8000_0000 to NAND Flash address 0x40_0000

Note: The Bytes information needs to be page size aligned!

Show bad NAND Flash blocks

nand bad

Description: Shows the bad NAND Flash blocks.

Show NAND FLash content

nand dump <NAND Flash address>

Example: nand dump 400000

Description: Shows the content of the specified NAND Flash block

LCD contoller

Show LCD controller settings

lcdinfo

Example:

 Display Resolution: 800 x 480 pixels
 Display Type:       Active Color Display
 Pixel Clock:        22 MHz
 Bits per Pixel:     16 Bits/Pixel
 Pixel Polarity:     Active High
 VSYNC Polarity:     Active Low
 HSYNC Polarity:     Active Low
 Clock Polarity:     Pos. Edge
 Output En Polarity: Active High
 HSYNC Puls Width:   64 Clock Cycles
 HSYNC Back Porch:   86 Clock Cycles
 HSYNC Front Porch:  42 Clock Cycles
 VSYNC Puls Width:   2 Line Cycles
 VSYNC Back Porch:   33 Line Cycles
 VSYNC Front Porch:  10 Line Cycles

GPIO's

Show DHCOM GPIO settings

gpioinfo

Example:

 GPIO_A: Direction = Input
         State     = 0
 GPIO_B: Direction = Input
         State     = 0
 GPIO_C: Direction = Input
         State     = 0
 GPIO_D: Direction = Input
         State     = 0
 GPIO_E: Direction = Input
         State     = 1
 GPIO_F: Direction = Input
         State     = 1
 GPIO_G: Direction = Output
         State     = 1
 GPIO_H: Direction = Input
         State     = 1
 GPIO_I: Direction = Input
         State     = 1
 GPIO_J: Direction = Input
         State     = 1
 GPIO_K: Direction = Input
         State     = 0

SD/MMC Card

Switch between MicroSD and SD Slot

mmcswitch <Slot number>

Example: mmcswitch 2

Description: Switch between SD/MMC Slots: 1 --> SD/MMC Slot, 2 --> MicroSD Slot

Initialize SD/MMC Card

mmcinit

Description: Initialize new inserted SD Card

Filesystem

Show Filesystem information

fatinfo <interface> <device>

Example: fatinfo mmc 1

Interface: MMC
 Device 1: Vendor: Man 094150 Snr 266e068c Rev: 1.0 Prod: AF UD
           Type: Removable Hard Disk
           Capacity: 121.2 MB = 0.1 GB (248320 x 512)
 Partition 1: Filesystem: FAT16 "NO NAME    "

List files

fatls <interface> <device> <directory>

Example 1: fatls mmc 1

Example 2: fatls mmc 1 /folder

Load Files from SD Card to SDRAM

fatload <interface> <device> <SDRAM address> <directory+filename>

Example 1: fatload mmc 1 80100000 nk.gz

Example 2: fatload mmc 1 80100000 /folder/nk.gz

Ethernet (TFTP)

Load File via TFTP to SDRAM

tftp <SDRAM address> <directory+filename>

Example: tftp 80100000 nk.gz

Example TFTP Server: "Winagents TFTP Server Manager"

Note: For TFTP download it is necessary to config the ENV variables "ipaddr" and "serverip"

Environment

Show ENV variables

printenv

bootdelay=0
baudrate=38400
ipaddr=192.168.55.230
serverip=192.168.55.36
gatewayip=192.168.55.36
netmask=255.255.255.0
frias=5
kernel=uImage
bootargs=console=ttymxc0,115200 root=/dev/mmcblk0p2
nandbootwince=update;bootwince 00200000
splashimage=0x000c0000
save_ENV_to_flash=setenv ENVinFlash 1; saveenv
ENVinFlash=1
ethaddr=00:04:a3:34:b6:0d
ethact=FEC0
winceimagetype=nk.gz
winceimagesize=00ba55ee
loadaddr=00200000
bootcmd=run nandbootwince
filesize=212050
Environment size: 449/262140 bytes

Set ENV variables

setenv <ENV name> <ENV value>

Example: setenv ipaddr 192.168.55.2

Note: If you need to edit "bootcmd" it is necessary to insert ";" between the unique commands. You can enter ";" at the command line with "\;".

Save ENV variables

saveenv

Update

Via iMX25_update.bmp file

For this update Type you need the "iMX25_update.bmp" file and the image file (e.g. nk.gz for WinCE) on the SD Card. After power on the update starts automatically. The "iMX25_update.bmp" file contains three pictures (Update in progress, Update done and Update error) wich are shown on the display during the update process. The file contains also an argument which defines the update type (WinCE image, Linux image, ...). An exact description can be found on the iMX25CreateUpdateBmp Manual.

Without iMX25_update.bmp file

WinCE

Registry Settings

LCD Controller

[HKEY_LOCAL_MACHINE\Drivers\Display\LCDC]
  "PanelType"=dword:1    ; LCD Panel identifier 
                         ; Description: Set "PanelType" = 0 to use the bootloader LCD controller settings, which can be programmed to NAND Flash via settings.bin file.
[HKEY_LOCAL_MACHINE\SYSTEM\GDI\ROTATION]
  "Angle"=dword:0        ; no rotation
                         ; "Angle"=dword:5A --> 90 degrees rotated clockwise
                         ; "Angle"=dword:B4 --> 180 degrees rotated clockwise
                         ; "Angle"=dword:10E --> 270 degrees rotated clockwise

Task Bar Look

[HKEY_LOCAL_MACHINE\Explorer]
  “QVGA“=dword:00000001  ; Change Task bar style: 0 --> normal Windows look, 1 --> PDA look