DHCOM STM32MP1-D2: Difference between revisions

From Wiki-DB
Jump to navigationJump to search
Line 71: Line 71:
==== [https://www.kernel.org Linux Kernel] ====
==== [https://www.kernel.org Linux Kernel] ====
* Mainline
* Mainline
:* [https://github.com/dh-electronics/linux-stm32mp1/tree/dev/5.4.69_dhsom DH 5.4.69 Development]
* [https://github.com/dh-electronics/linux-stm32mp1/tree/dev/5.4.69_dhsom DH 5.4.69 Development]
* [https://github.com/dh-electronics/dhcom_stm32mp1-bsp-platform '''NEW''' Yocto meta layer --> Github]


== Download binaries/images ==
== Download binaries/images ==
Note: Based on kernel 5.10.x and Yocto version dunfell
Note: Based on kernel 5.10.x and Yocto version dunfell
* [https://xxx '''NEW''' DH Mainline based Starter Image]
* [https://xxx '''NEW''' DH Mainline based Starter Image]

Revision as of 08:48, 11 February 2021

DHCOM STM32MP1-D2

DHCOM STM32MP1-D2

Hardware

  • Dual ARM Cortex®-A7 up to 650 MHz and Single ARM Cortex®-M4 up to 209 MHz
  • 3D GPU OpenGL® ES2.0 up to 533 MHz, Power Management: STPMIC1A
  • TrustZone, cryptography, hash, secure boot
  • DDR3L: 256 / 512 / 1024 Mbyte (32 bit)
  • eMMC flash: 4 / 8 / 16 GB
  • 2 MByte SPI boot flash
  • 256 byte EEPROM
  • WiFi / Bluetooth: WiFi IEEE 802.11 a/b/g/n, 802.11j (hosted mode) with dual band, Bluetooth® v5.0 (BR/EDR/BLE), PCB antenna and U.FL antenna connector
  • On-board microSD card socket
  • RTC with temperature compensation ± 3.0 ppm between -40 to +85°C
  • Supply voltage range: 3.3 or 5.0 VDC / typ. 1 W-1.5 W (without WiFi/BT)
  • Industrial temperature range (-40°C to +85°C)
  • SODIMM-200 socket with DHCOM pin assignment
  • JTAG debug connection via FFC plug connector or Tag-Connect
  • Bus interface: 16 bit asynchron address/data bus, 1 CS
  • Ethernet 1: 10 / 100 Mbit with PHY, IEEE 1588v2
  • Ethernet 2: 10 / 100 Mbit with PHY
  • MMC/SD interface: 4 bit mode
  • CAN 1: V2.0B and CAN FD V1.0, TTCAN (time triggered)
  • CAN 2: V2.0B and CAN FD V1.0
  • UART 1: Rx / Tx / Rts / Cts, up to 12.5 Mbit/s
  • UART 2: Rx / Tx / Rts / Cts, up to 12.5 Mbit/s
  • UART 3: Rx / Tx, up to 12.5 Mbit/s
  • SPI 1: max. 50 Mbit/s
  • I2C 1: max. 1 Mbit/s
  • I2C 2: max. 1 Mbit/s
  • USB host 1: High-Speed
  • USB OTG: High-Speed
  • Parallel camera: 10 bit interface up to 140 Mbytes/s
  • Display RGB: Max. 1366 x 768 pixels, 24 bit
  • MIPI®-DSI 2 data lanes up to 1 GHz each
  • Touch: 4-wire
  • I²S Audio interface
  • GPIOs: 24 IOs
  • PWM: 1x 16 bit
  • Analog: 4x 16 bit ADC and 2x 12 bit DAC

Software Support

BSP Sources

U-Boot

Linux Kernel

Download binaries/images

Note: Based on kernel 5.10.x and Yocto version dunfell