DHSBC STM32MP13

The DHSBC STM32MP13x board is the official DHCOR STM32MP13 reference design!

Introduction

Reference design for secure industrial IoT devices based on STM32MP13x

• Single Board Computer based on the solderable DHCOR STM32MP13
• Compatible with accessories from the Raspberry Pi© community
• Highlights: Bluetooth / WiFi, Dual GB Ethernet, Secure Boot, OP-TEE support
• Trusted Platform Module 2.0 available on request
• Mainline Linux support and active software maintenance
• Industrial product design with CE certification
• Guaranteed long-term availability of 10+ years

Technical Details

STM32MP135F 1x ARM® Cortex-A7 up to 1 GHz PMIC STPMIC1D DDR3 DRAM 512 Mbyte @ 533 MHz eMMC Flash 4 Gbyte NOR Flash 4 Mbyte, Quad SPI interface EEPROM 4 kbyte RTC temp. compensated RV-3032-C7 USB Host 1x type A, 2.0 high-speed USB Device 1x Type-C, 2.0 high-speed WiFi / Bluetooth WiFi 2.4GHz IEEE 802.11b / g / n Bluetooth® v5.2 (BR/EDR/BLE) Antenna: U-FL connector Ethernet 10 / 100 / 1000 Mbit/s, IEEE 802.3-compliant

TPM (Trusted Platform Module)2.0 device ST33TPHF2XSPI Push-Buttons Power and reset Battery Socket CR1216, CR1220 and CR1225 Boot Mode 3 bit boot mode switch Debug Interface JTAG interface via tag-connect Supply (SYS_DCIN) 8 - 18 VDC Temperature Range 0 - 40 °C Dimensions 85 x 56 mm Raspberry Pi 40-pin Expansion 2 x UART 1 x I2C 1 x I2S 1 x SPI 2 x PWM 2 x CAN up to 28 x GPIOs

Downloads

• DH Mainline based starter image 2024-07-03 (based on 6.6 Linux Kernel)

Documentation

• Getting-Started with DHSBC STM32MP13 (R02)
• DHCOR STM32MP13 User Manual R01 IMPORTANT: Please have a look at chapter 26. Hardware design checklist

Design Files

• DHSBC STM32MP13 Schematic
• DHSBC STM32MP13 3D STEP file
• DHCOR STM32MP13 Allegro/layout symbol
• DHCOR STM32MP13 3D STEP file

Software

DH Mainline based Linux

• Build your own Yocto Scarthgap LTS via kas (GitHub)
• Yocto BSP meta layer (Github)

Useful instructions

Setup new board and install image files via USB (dfu and ums mode) / U-Boot recovery via DFU

• DHSBC STM32MP13 DFU and UMS uasge

How to connect to WiFi network with WPA2 PSK?

Establish connection

wpa_passphrase "SSID" > /etc/wpa_supplicant.conf

-> In the next step, please enter the password

rfkill unblock all

ip link set wlansom0 up

wpa_supplicant -B -i wlansom0 -c /etc/wpa_supplicant.conf

udhcpc -i wlansom0

Disconnect

ip link set wlansom0 down

Add support for joy-it RB-TFT3.2V2 SPI display

Add Device Tree oeverlay to u-boot.

=> setenv loaddtos '#conf-stm32mp135f-dhcor-dhsbc.dtb#conf-stm32mp13xx-dhcor-dhsbc-overlay-rb-tft32-v2.dtbo'

=> saveenv

=> saveenv

• Link: joy-it RB-TFT3.2V2

Links

• DH DHCOR STM32MP13
• DH DHSBC STM32MP13
• STM32 MPU wiki
• STM32 MPU wiki - Device tree configuration
• STM32MP13 resources